Fault codes, also called error codes or fault codes, allow your device to automatically report an internal malfunction. Below you will find the list of fault codes for your Beko dryer and their meaning: this will give you an indication to best diagnose the origin of the malfunction of your appliance.
The error code can be read directly on the front panel of your Beko dryer. Depending on the model, you can read this code on a display (for example, “Err 01”) or by observing the number of LED flashes (for example: 4 LED flashes = “Err 04”).
Refer to the instructions for your Beko dryer to find out the exact meaning of the fault code displayed or the lights that flash. The number of flashes often corresponds to the error code number, but there are specificities linked to each model and brand.
ERROR CODE ER01 – DOOR OPEN
This error code indicates that the appliance door is open during operation.
- Check that you have closed the door properly and that nothing is blocking its closing.
- If everything is securely closed and the error persists, check the door safety, which could misinterpret the position of the lock.
ERROR CODE ER02 – TOO MUCH WATER
This fault code indicates an error in the signal sent by the float, which may indicate an overflow of water in the drain circuit.
- Electrically control the drain pump, also called the condensed water pump, located in the lower part of the device. Replace it if it does not work.
- If the error does not disappear, check the cold air fan or replace the electronic board.
ERROR CODE ER04 / ER05 – NTC PROBES
These error codes concern the CTN temperature probes, located in the air circuit:
- The CTN probe is considered cut off (Er04)
- The NTC probe is short-circuited (Er05)
Check the connections of the probe concerned and replace it if necessary.
ERROR CODE ER08 / ER09 – DOOR SECURITY
These error codes concern door security:
- Door safety is considered to be off (Er08)
- The lock system is short-circuited (Er09)
Check the door safety and replace it if necessary.
ERROR CODE ER10 / ER11 – NTC PROBES
These error codes concern the CTN temperature probes, located near the compressor:
- The CTN probe is considered cut off (Er10)
- The NTC probe is short-circuited (Er11)
Check the connections of the probe concerned and replace it if necessary.
ERROR CODE ER12 – HUMIDITY DETECTORS
This error code is displayed when the humidity detectors still detect significant humidity in the machine even though the program has finished.
- Clean the different filters present in the dryer
- Check the humidity detectors (sensors or probes), as well as the resistance (or heat pump) and the fan.
ERROR CODE ER13 – LOW CHARGE
This fault code is displayed when the device considers that there is not enough laundry in the drum. This low load can cause problems, so it is not recommended to start a program with too few laundry to dry.
ERROR CODES ER14 / ER15 – SUPPLY VOLTAGE
These codes indicate that the power supply voltage to the dryer is incorrect. It is either less than 165 volts or it exceeds 265 volts.
Try plugging your device into another outlet, other than a power strip. If the problem persists, have your electrical installation checked by a professional.
ERROR CODE ER16 – DOOR OPEN
This code signals pressing the start button while the door is still open.
If you want to start a program, make sure to close the door before starting the cycle.
ERROR CODE ER17 – DOOR OPEN
This error code indicates that the appliance door is open during operation.
- Check that you have closed the door properly and that nothing is blocking its closing.
- If everything is securely closed and the error persists, check the door safety, which could misinterpret the position of the lock.
ERROR CODE ER18 – ELECTRONIC CARD COMMUNICATION
This error code indicates a communication problem between the power board and the display board.
- Check the connections on the different cards.
- Contact a technician if the error persists.
ERROR CODE ER19 – PROGRAM INTERRUPTED
This code means that the program was interrupted by the user. This does not require any special action, just turn off the device to restart it.
ERROR CODE ER20 – SHUTDOWN DURING OPERATION
This error code is displayed when pressing the start/stop button is detected during a drying program. To stop a program while it is running, look for a button on your appliance dedicated to stopping during drying.
ERROR CODE ER21 / ER22 – DRYING STOPPED
This fault code occurs even though the drying program has stopped. This is due to repetitive shutdowns of the compressor (heat pump). If possible, replace this part, or contact a technician.
ER27: Lint Filter Sensor Fault
The sensor that monitors the status of the lint filter is malfunctioning or providing inaccurate readings.
ER28: Drum Rotation Issue
This error suggests a problem with the drum’s rotation mechanism, potentially causing uneven drying.
ER29: Gas Flow Restriction
If your dryer is a gas dryer, this error indicates a restriction in the gas flow, affecting heating and drying performance.
ER30: Control Board Communication Error
There’s a communication problem between the control board and other components of the dryer, leading to various malfunctions.
ER31: Heating Element Fault
This error code points to a problem with the heating element, which is responsible for generating heat for drying.
ER32: Cool Air Duct Blockage
The duct that supplies cool air to the dryer is blocked or restricted, affecting temperature control.
ER33: Exhaust Fan Error
This error suggests a malfunction in the exhaust fan, which plays a crucial role in maintaining proper airflow.
ER34: Drum Belt Tension Error
The tension of the drum belt is incorrect, potentially causing issues with drum rotation.
ER35: Dryer Door Sensor Issue
The sensor responsible for detecting the status of the dryer door is malfunctioning or providing inaccurate readings.
ER36: Water Reservoir Sensor Error
If your dryer has a water reservoir, this error indicates a problem with the sensor that monitors the reservoir’s status.
ER37: Ventilation Fan Malfunction
This error indicates a malfunction in the dryer’s ventilation fan, which is essential for proper airflow during drying cycles.
ER38: Drying Sensor Calibration Error
The sensor responsible for detecting moisture levels in the laundry is not calibrated correctly, affecting drying accuracy.
ER39: Thermal Fuse Tripped
The thermal fuse in the dryer has tripped due to excessive heat, preventing further operation until the issue is resolved.
ER40: Drum Bearing Problem
This error code points to an issue with the drum’s bearing or support system, potentially causing unusual noises during operation.
ER41: Gas Valve Issue
If your dryer is a gas dryer, this error suggests a problem with the gas valve, affecting the flow of gas for heating.
ER42: Exhaust Temperature Sensor Error
The sensor that monitors exhaust temperature is malfunctioning or providing inaccurate readings.
ER43: Cool Down Phase Delay
This error indicates a delay or malfunction in the cool-down phase at the end of a drying cycle.
ER44: Electrical Connection Problem
There’s a problem with the electrical connection of the dryer, potentially affecting various components and functions.
ER45: Airflow Sensor Error
The sensor responsible for monitoring airflow in the dryer is providing inaccurate readings or experiencing a malfunction.
ER46: Water Leak Detected
The dryer has detected a water leak, which can lead to damage or safety concerns.
ER47: Exhaust Duct Sensor Fault
The sensor that monitors the status of the exhaust duct is malfunctioning or providing inaccurate readings.
ER48: Lint Filter Reminder
This is not an error code but a reminder that it’s time to clean the lint filter to maintain dryer efficiency.
ER49: Condensation Tank Overflow
If your dryer has a condensation tank, this error indicates that it has overflowed due to a drainage issue or blockage.
ER50: Drum Misalignment
This error suggests a misalignment or imbalance issue with the dryer’s drum, potentially causing noise and vibration.
ER51: Cool Air Thermostat Error
The thermostat responsible for controlling the cool air supply is malfunctioning or providing inaccurate readings.
ER52: Drum Drive Motor Fault
This error code points to a problem with the drum drive motor, impacting the drum’s rotation.
ER53: Power Supply Fluctuation
This error indicates that the dryer has detected fluctuations in the power supply voltage, which can affect operation.
ER54: Exhaust Duct Temperature Error
The sensor that monitors the exhaust duct’s temperature is malfunctioning or providing inaccurate readings.
ER55: Inlet Valve Sensor Issue
The sensor responsible for monitoring the inlet valve’s status is malfunctioning or providing inaccurate readings.
ER56: Gas Ignition Sensor Fault
If your dryer is a gas dryer, this error suggests a problem with the gas ignition sensor, affecting the burner’s operation.
ER57: Cycle Timer Error
This error code indicates a problem with the dryer’s cycle timer, potentially causing irregular cycle durations.
ER58: Heating Element Sensor Fault
The sensor responsible for monitoring the heating element is malfunctioning or providing inaccurate readings.
ER59: Drum Belt Motor Error
This error suggests a problem with the motor responsible for the drum belt’s operation.
ER60: Exhaust Fan Sensor Issue
The sensor that monitors the exhaust fan’s status is malfunctioning or providing inaccurate readings.
ER61: Display Panel Communication Error
This error indicates a communication problem between the display panel and other components of the dryer.
ER62: Overloading Detected
The dryer has detected that it’s overloaded with laundry, which can lead to uneven drying and excessive wear on components.
ER63: Drum Temperature Adjustment Error
This error code points to a problem with the adjustment of the drum’s temperature during the drying cycle.
ER64: Moisture Sensor Calibration Fault
The sensor responsible for calibrating moisture levels in the laundry is not functioning correctly.
ER65: Water Inlet Valve Sensor Error
The sensor that monitors the water inlet valve’s status is malfunctioning or providing inaccurate readings.
ER66: Exhaust Filter Replacement Reminder
This is not an error code but a reminder to replace the exhaust filter at regular intervals to maintain dryer performance.
ER67: Motor Belt Tension Error
The tension of the motor belt is not within the expected range, affecting the drum’s rotation.
ER68: Lint Duct Blockage
The duct responsible for collecting lint is blocked or obstructed, affecting airflow and drying efficiency.
ER69: Drum Support Roller Issue
This error indicates a problem with one of the drum support rollers, potentially causing noise during operation.
ER70: Exhaust Temperature Control Error
The temperature control system for the exhaust air is not functioning correctly, affecting drying performance.
ER71: Water Pump Motor Error
If your dryer has a water pump, this error suggests a problem with the pump motor, impacting moisture removal.
ER72: Vent Hose Connection Fault
The vent hose is not properly connected or is experiencing a fault, affecting airflow and drying efficiency.
ER73: Gas Valve Ignition Delay
If your dryer is a gas dryer, this error indicates a delay in igniting the gas burner.
ER74: Control Panel Display Error
This error suggests a malfunction in the control panel’s display or interface.
ER75: Cool Down Fan Error
The fan responsible for the cool-down phase at the end of a cycle is not functioning correctly.
ER76: Ambient Temperature Sensor Issue
The sensor that monitors the ambient temperature around the dryer is malfunctioning or providing inaccurate readings.
