The washer-dryer, also called a washer-dryer, is a household washing machine that has an integrated drying program. It works on an internal heating system, thanks to the heating element.
The heating element of a washer-dryer is a heating assembly made up of resistors, the temperature sensor and the drying duct. Depending on time and use, it happens that this part breaks down.
The heating assembly can be replaced if you notice the following faults:
- laundry dries poorly,
- the device takes time to dry,
- the drying program is long,
- the laundry is wet at the end of the programme,
- laundry does not dry.
In order to avoid this kind of problem, it is strongly recommended to replace it without further delay. This is something you can do on your own.
The heating element on a washing and drying machine is located inside, on the side of the upper facade, whose drying duct is connected to the porthole seal which must be removed.
The drying element in a washer-dryer is responsible for generating heat to dry your clothes during the drying cycle. Over time, the drying element can wear out or become damaged, resulting in inefficient drying or a complete failure of the drying function. If you notice that your washer-dryer is not drying clothes effectively, it may be necessary to replace the drying element. Changing the drying element requires some technical knowledge and the use of appropriate tools. In this guide, we will walk you through the steps to change the drying element on a washer-dryer.
Safety Precautions
Before starting any repair work on your washer-dryer, it is important to prioritize safety. Always unplug the machine from the power source before attempting any repairs. Additionally, ensure you are working in a well-ventilated area and wear protective gloves to prevent injury.
Tools Required
To change the drying element on a washer-dryer, you will need the following tools:
- Screwdriver set (Phillips or Torx, depending on your machine)
- Pliers
- Towels or rags (to protect the floor and clean up any spills)
Steps to Change the Drying Element
Follow these steps to change the drying element on a washer-dryer:
Step 1: Unplug the Washer-Dryer
Ensure the washer-dryer is disconnected from the power source by unplugging it from the wall socket.
Step 2: Access the Drying Element
To access the drying element, you may need to remove the back panel or a portion of the machine’s casing. Consult your washer-dryer’s user manual or search online for specific information about accessing the drying element in your particular model.
Step 3: Disconnect the Electrical Connections
Locate the electrical connections that supply power to the drying element. These connections are usually attached with screws or clips. Use a screwdriver or pliers to disconnect the electrical connections, ensuring you keep track of which wire is connected to which terminal.
Step 4: Remove the Drying Element
Once the electrical connections are disconnected, carefully remove any screws or fasteners that secure the drying element in place. Take note of their positions or use a marker to label them for proper reinstallation.
Step 5: Install the New Drying Element
Take the new drying element and position it in place of the old one. Ensure it is aligned correctly and fits snugly. Insert and tighten the screws or fasteners to secure the new drying element in place.
Step 6: Reconnect the Electrical Connections
Reconnect the electrical connections to the new drying element, ensuring you connect the wires to the corresponding terminals. Use the appropriate screws or clips to secure the connections.
Step 7: Reassemble the Washer-Dryer
Once you have completed the drying element replacement, reassemble any covers or panels you removed earlier to access the drying element. Use the appropriate screws or fasteners to secure these components back in place.
Step 8: Test the Machine
Plug your washer-dryer back into the power source. Turn it on and run a test drying cycle. Observe the machine’s operation, ensuring that the new drying element generates heat and effectively dries the clothes. Monitor the temperature and check for any unusual noises or issues. If the machine operates correctly without any problems, it indicates that the new drying element is properly installed.
If you encounter any persistent problems or suspect a fault with the drying element despite the replacement, it is recommended to consult a professional appliance repair technician or contact the manufacturer for further assistance.
In conclusion, changing the drying element on a washer-dryer requires some technical knowledge and attention to detail. By following these steps and using the appropriate tools, you can successfully replace a worn-out or damaged drying element and restore the proper drying functionality of your washer-dryer. Always refer to your washer-dryer’s user manual for specific instructions and guidelines, as different models may have slight variations in the drying element replacement process. Regular maintenance and prompt drying element replacement will help ensure the optimal performance of your washer-dryer.
“If you’re in Toronto or the Greater Toronto Area and need your fix washing machine Toronto urgently, contact Shymon Appliance Repair, we know how to fix it!”
