How to Change the Switches on a Steam Cleaner

Aug 06, 2023, 15:15pm

The steam cleaner is a device used to clean different surfaces, simply with water vapor and without product or detergent. It can be used on glass or hard floors, as well as rugs and carpets. The surface to be cleaned influences the type of cleaner: sled, hand or broom. Very hot water vapor is produced from the water put in the tank.

The device is controlled from the buttons on the control panel. Switches are parts that wear out easily after many uses. After a while, they may not work at all.

If your device no longer starts or the controls do not respond, then it is possible that the switches are faulty and need to be changed.

The location of the switches on a steam cleaner differs depending on the type of device. In general, they are found near the handle allowing the manipulation of the device.

Steam cleaners are powerful tools that use the force of hot, pressurized steam to clean and sanitize a variety of surfaces. While they are built to be reliable and long-lasting, there are instances when parts might fail due to wear and tear. One such part that might need replacement is the switch.

The switch on a steam cleaner controls the flow of electricity, allowing the device to turn on and off. If the switch is broken or defective, it can affect the performance of your steam cleaner, preventing it from turning on or functioning properly. This guide provides a step-by-step process on how to change the switches on a steam cleaner.

How to Change the Switches on a Steam Cleaner

Step 1: Gathering Necessary Tools

First, you will need a set of tools. Typically, these include:

  • A new switch compatible with your steam cleaner model
  • A screwdriver (typically Phillips-head or flat-head, depending on the screws)
  • Needle-nose pliers
  • Safety gloves and goggles

Before you begin, make sure that you have all these tools within reach.

Step 2: Disconnect the Steam Cleaner from the Power Supply

This is an important safety measure. Make sure the steam cleaner is turned off and unplugged from the power source. Never work on any electrical device while it’s connected to a power supply.

Step 3: Open the Steam Cleaner’s Housing

Look for screws around the steam cleaner’s housing. Use your screwdriver to remove these screws and gently lift off the housing, revealing the internal components. Make sure to keep the screws in a safe place as you’ll need them to reassemble the device.

Step 4: Identify the Switch

Locate the switch within the internal components of the steam cleaner. It is usually a small plastic component with two or more wires connected to it. If you’re having trouble finding it, consult your steam cleaner’s user manual.

Step 5: Remove the Old Switch

Now that you’ve identified the switch, carefully remove it. Start by disconnecting the wires attached to the switch using your needle-nose pliers. Be gentle to avoid damaging the wires.

Once the wires are removed, proceed to detach the switch from its place. It might be secured with screws, clips, or may simply pop out depending on your specific model.

How to Change the Switches on a Steam Cleaner

Step 6: Install the New Switch

Take the new switch and connect it to the wires you previously disconnected from the old switch. Ensure you connect the wires correctly as they were in the old switch. After connecting the wires, place the new switch in the spot where the old switch was situated.

Step 7: Close the Housing

With the new switch properly installed, it’s time to put everything back together. Replace the housing cover and fasten it securely with the screws you removed earlier.

Step 8: Test the Device

Finally, reconnect your steam cleaner to the power supply and test the device. If you’ve followed the steps correctly, your steam cleaner should now be working as it should with the new switch.


While replacing the switch on a steam cleaner might seem intimidating, with the right tools and guidance, it can be a fairly straightforward DIY task. This guide should have provided you with all the information needed to successfully change the switches on your steam cleaner.

Remember, if you’re ever unsure about a step or feel uncomfortable doing this on your own, don’t hesitate to call a professional. Safety should always come first when dealing with electrical appliances.