Fault codes, also called error codes or fault codes, allow your device to automatically report an internal malfunction. Below you will find the list of fault codes for your Siemens tumble dryer and their meaning: this will give you an indication to best diagnose the origin of the malfunction of your appliance.
The error code can be read directly on the front panel of your Siemens dryer. Depending on the model, you can read this code on a display (for example, “Err 01”) or by observing the number of LED flashes (for example: 4 LED flashes = “Err 04”).
Refer to the user manual for your Siemens device to find out the exact meaning of the fault code displayed or the lights that flash. The number of flashes often corresponds to the error code number, but there are specificities linked to each model and brand.
ERROR CODE E01 OR E2040 / E02 OR E20A1
This error code indicates overheating of the device.
- First check the lint filter and clean it if necessary.
- If the error persists, check that the air circuits are not blocked.
ERROR CODE E03 OR E3040
This fault code indicates that the condensed water tank is full.
- Empty this reservoir used to collect water from steam, usually located on the bottom of the dryer.
- If the error persists, check the pump near the tank and the cold air fan.
ERROR CODE E04 OR E9100
This fault code signals too much load in the dryer drum.
- Check that you have not put too much laundry, which can be heavy if wet.
- Try running a program with a lighter load or change programs.
ERROR CODE E06 OR E2013
This code indicates a fault in the drying resistor circuit.
- The lint filter may be blocked, clean it if necessary.
- If the error persists, check the drying resistance.
ERROR CODE E08 OR E2022 / E09 OR E2012
This code indicates that the NTC temperature sensor is defective.
Check the probe connections and replace it if necessary to resolve the error.
ERROR CODE E10 TO E13
This type of error code indicates a programming error in the software.
Refer to your user manual in case a reset is possible, or contact a brand repair center.
ERROR CODE E16 OR 8031
This code indicates that the door is open while the appliance is operating.
- Check that you have closed the door securely.
- If so and the error persists, reduce the load.
- Then check the door security system and its connections.
- Replace the door security if it is defective: it may consider that the door is open when it is not.
ERROR CODE E22 / E23
This fault code indicates a problem with the power supply to the dryer. The device is either at too low voltage (E22) or at overvoltage (E23).
- Check that the device is plugged in securely, and test the power cable and plug.
- Plug the device into another outlet and avoid connecting it to a power strip.
- If the problem persists, you will need to have the electrical installation checked by a professional.
ERROR CODE E28
This code indicates that the NTC temperature sensor is defective.
Test and verify probe connections and replace if necessary.
ERROR CODE E56
This fault code indicates that communication is defective or impossible with the control module.
Check the cables connected to the electronic boards and replace the control module if the error persists.
ERROR CODE E63 / E67 / E90
This fault code indicates a failure of the power module and the electronic card. This can result in communication and programming problems and prevent other organs from functioning.
Replace the power electronics board to resolve the problem.
ERROR CODE E91
This fault code indicates that communication is defective or impossible with the control module.
Check the cables connected to the electronic boards and replace the control module if the error persists.
ERROR CODE E92
This fault code indicates a problem with the power supply voltage of the dryer: the voltage supplying the device is not correct.
- Check that the device is plugged in securely, and test the power cable and plug.
- Plug the device into another outlet and avoid connecting it to a power strip.
- If the problem persists, you will need to have the electrical installation checked by a professional.
ERROR CODE F09
This code indicates that the NTC temperature sensor is defective.
Test and verify probe connections and replace if necessary.
ERROR CODE F11
This error code concerns the operation of the engine.
- Check the belt, the motor, the starting capacitor, after having discharged it for safety.
- Check the electronic card for signs of wear or burns. If this is the case, it will need to be replaced.
ERROR CODE F12
This error code concerns the operation of the engine.
- Check the motor, the starting capacitor, after discharging it for safety.
- Check that there are no signs of wear or burns on the electronic card. Otherwise, it will have to be replaced.
E100: Cloud connectivity error
For smart dryers with cloud connectivity features, there’s a problem connecting to the cloud service.
E101: Multiple sensor failure
Multiple sensors within the dryer have malfunctioned or are giving conflicting readings.
E102: Drum rotation direction error
The drum’s rotation direction is inconsistent with the set or expected direction.
E103: Power backup fault
For dryers with a power backup feature, there’s an issue with the backup system.
E104: Filter cleaning reminder fault
The system’s automatic reminder to clean filters is malfunctioning.
E105: Load type detection error
The dryer has trouble detecting or categorizing the type of load inside.
E106: Audio alert malfunction
The audio alert or beep system of the dryer is not working as intended.
E107: Door hinge error
The door hinge is malfunctioning or not positioned correctly.
E108: Component aging error
The dryer has detected that one or more components have aged beyond a certain threshold and may need replacement.
E109: Language setting error
There’s an issue with the language settings or language pack in the dryer’s interface.
E110: Overload protection trigger
The dryer’s system to prevent overload, either by weight or volume, has been activated.
E111: Ambient humidity error
The dryer detects an abnormal ambient humidity level that might affect its efficiency.
E112: Static electricity error
There’s an excessive buildup of static electricity inside the dryer.
E113: Hardware calibration fault
The dryer’s internal hardware components require calibration or are giving out-of-range readings.
E114: Cycle sequence error
The dryer’s internal cycle sequence or program has been disrupted.
E115: Duct blockage detection
The dryer’s duct system, used for airflow, has been detected as blocked or restricted.
E116: Motor torque error
The motor’s torque or rotational force is inconsistent with the set or expected levels.
E117: Display brightness error
The display or screen’s brightness level is malfunctioning.
E118: Backup memory fault
The backup memory, where the dryer stores essential data, is malfunctioning.
E119: Internal cleaning required
The dryer’s internal cleaning system or reminder is indicating a need for maintenance.
E120: Touch sensitivity error
The touch-sensitive controls of the dryer are not responding adequately or are overly sensitive.
E121: Firmware compatibility error
There’s a compatibility issue between the dryer’s firmware and some hardware components.
E122: Anti-vibration system fault
The system designed to reduce vibrations during operation is malfunctioning.
E123: Safety interlock error
A safety feature preventing operation under certain conditions is malfunctioning.
E124: User preference saving error
The dryer is unable to save user preferences or custom settings.
E125: Data transmission error
The dryer, especially if it’s a smart model, is having issues transmitting data to external devices or networks.
E126: Internal ventilation fault
The system responsible for internal ventilation is malfunctioning.
E127: Battery backup error
For dryers with a battery backup for settings or alarms, there’s a malfunction.
E128: Sensor calibration overdue
Sensors within the dryer need recalibration, either due to time or detected drift.
E129: Component overheating warning
While not a fault, the dryer is warning of a component nearing an overheating condition.
E130: Operating volume error
The operational noise level of the dryer is outside the expected range.
E131: Inlet airflow restriction
The dryer detects a restricted airflow at its inlet, possibly due to obstructions or a malfunctioning fan.
E132: Outlet exhaust error
There’s an issue with the outlet exhaust, which might be leading to inefficient moisture removal.
E133: Load balancing error
The dryer’s system for balancing the load within the drum is malfunctioning or has detected an imbalanced load.
E134: Remote activation error
For smart dryers with remote activation features, the system is not responding to remote signals.
E135: Interior light fault
The interior light of the dryer, if present, is malfunctioning or not turning on.
E136: Moisture collection tray full
For dryers with moisture collection trays, the tray is detected as full and needs emptying.
E137: Energy monitoring fault
The dryer’s energy consumption monitoring system is malfunctioning or giving incorrect readings.
E138: Extended pause error
The dryer has been paused for an extended duration and may need user intervention.
E139: Connectivity hardware fault
For connected dryers, the hardware enabling Wi-Fi or other forms of connectivity is malfunctioning.
E140: UV sanitation malfunction
For dryers with UV sanitation features, the UV system is not working as intended.
E141: Component lifespan warning
The dryer has detected that a specific component is nearing the end of its recommended lifespan.
E142: Incomplete update error
A firmware or software update was not completed successfully and may need to be restarted.
E143: Memory overflow error
The dryer’s onboard memory is near capacity, which might affect performance.
E144: Anti-wrinkle feature malfunction
The system designed to reduce or prevent wrinkles in dried clothes is malfunctioning.
E145: Steam feature error
For dryers with steam features, there’s an issue with the steam generation or application system.
E146: Thermal sensor drift
Thermal sensors within the dryer are giving readings that drift from expected values.
E147: Internal communication
latency Communication between internal components is experiencing latency or delay.
E148: Proximity sensor fault
Any proximity sensors, used to detect nearby objects or the position of the door, are malfunctioning.
E149: User interface freeze
The user interface, whether touch screen or buttons, has frozen and is unresponsive.
E150: Hardware redundancy error
For dryers with redundant hardware components for safety or performance, there’s a malfunction in one of the redundant systems.
E151: Detergent or fragrance dispense error
For models with fragrance or detergent features, the system is not dispensing as intended.
E152: Condensation error
The system meant to manage or reduce condensation within the dryer is malfunctioning.
E153: Internal clock fault
The dryer’s internal clock or timer, responsible for tracking and managing cycle durations, is malfunctioning.
E154: Data backup error
For smart dryers with data backup features, there’s an error backing up data.
E155: Self-diagnostic tool error
The built-in tool designed to diagnose problems with the dryer is itself malfunctioning.
E156: Control board temperature fault
The main control board of the dryer is overheating or not within the normal temperature range.
E157: Drum illumination fault
Any lights used to illuminate the drum’s interior are not working correctly.
E158: Water detection error
Sensors meant to detect water or moisture levels are malfunctioning.
E159: User authentication error
For smart dryers with user authentication features, the system is not recognizing authorized users.
E160: Load detection calibration error
The calibration of sensors meant to detect the weight or amount of load is off.
E161: Residual detergent detection
The dryer has detected residual detergent on clothes, which could affect drying efficiency or result in residue.
E162: Ambient light sensor fault
Any sensors used to detect ambient light for adaptive display brightness or other features are malfunctioning.
E163: External interference detected
The dryer detects interference from external devices or networks, which may affect its smart features.
E164: Humidity control malfunction
For dryers with active humidity control, the system isn’t maintaining desired humidity levels.
E165: Sound dampening system fault
The system designed to dampen or reduce noise during operation is not effective.
E166: Refresh cycle error
Any cycle meant to refresh clothes without a full dry is not operating correctly.
E167: Load size mismatch
The detected load size doesn’t match the size selected by the user.
E168: Color protection feature fault
For models with color protection features, the system is not working as intended.
E169: Auto shutoff error
The dryer’s automatic shutoff, meant to save energy or act as a safety feature, is malfunctioning.
E170: User profile synchronization error
For dryers with multiple user profiles, there’s an issue synchronizing preferences across profiles.
E171: Software rollback error
An attempt to rollback the dryer’s software to a previous version has failed.
E172: Carbon filter change reminder fault
For models with carbon filters, the reminder system to change or clean the filter is malfunctioning.
E173: Air intake error
The dryer has trouble drawing in air, possibly due to blockage or a fan malfunction.
E174: Auto-cleaning cycle fault
Any automatic cleaning cycles for the dryer’s interior are not functioning correctly.
E175: Weight sensor calibration error
The sensors meant to determine the weight of the clothes load need recalibration.
E176: Sleep mode malfunction
For dryers with energy-saving sleep modes, the mode isn’t activating or deactivating correctly.
E177: Drum alignment fault
The drum is misaligned or not rotating on its intended axis.
E178: Thermal cutoff reset error
The thermal cutoff, a safety feature, has tripped and requires resetting. It may also fail to reset.
E179: Touch panel alignment error
The touch panel or touchscreen isn’t aligned correctly with the display or isn’t responding accurately to touches.
E180: Predictive maintenance fault
For smart dryers with predictive maintenance features, the system isn’t forecasting or detecting potential issues correctly.
E181: Mobile app connectivity error
For dryers with associated mobile apps, there’s a connectivity or compatibility issue with the app.
E182: Cycle customization error
For dryers allowing custom cycle creations, there’s an error saving or loading custom cycles.
E183: Overcurrent protection trigger
The dryer’s system to protect against excessive electrical current has been activated.
E184: Drum humidity sensor drift
Sensors that detect humidity levels inside the drum are not consistent with expected readings.
E185: Power frequency fluctuation error
The dryer detects fluctuations in the frequency of the supplied power, which may affect operation.
E186: Remote diagnostic fault
For dryers with remote diagnostic capabilities, the feature isn’t working correctly.
E187: Anti-allergen cycle fault
Any cycles designed to reduce allergens are not functioning correctly.
E188: Standby power consumption error
The dryer consumes more power in standby mode than expected.
E189: Lint sensor error
Sensors designed to detect lint buildup are malfunctioning or require cleaning.
E190: Drum rotation counter error
Any systems counting drum rotations for diagnostics or cycle tracking are malfunctioning.
